Home > Pkgadd Error > Pkgadd Error Request Script Did Not Complete Successfully

Pkgadd Error Request Script Did Not Complete Successfully

Workaround: Create the mirrored file systems with Solaris Volume Manager software, then create the new boot environment with the lucreate command. More typically, this problem is observed in Sun Blade 2000 workstations that have the XVR-1000 graphics accelerator installed. Sun Patch Manager Tool 2.0 Not Compatible With Previous Versions A system that runs the Sun Patch Manager Tool 2.0 can manage remote systems that run Patch Manager Tool, including Sun Workaround: Follow these steps. useful reference

You're now being signed in. The SVR4 ABI states that the checkinstall shall only be used as an information gathering script. Workaround: Follow these steps. pkgadd question binary pkgs White Papers & Webcasts VMware Virtual SAN Ready Nodes VMware EVO-Rail VMware EVO-Rail Hyper Converged Infrastructure Appliance Software Defined Storage - The Missing Link for Cloud and http://www-01.ibm.com/support/docview.wss?uid=swg21382167

The problem might be more prevalent if the kernel debugger (kadb) is active. You find the check install script says you need to run the license script, but you accepted the license agreement. However, no notification about these problems was being generated.

Then use the patchadd command to install the patches from the directory on the local system where the patches were copied. Previous: Chapter 1 Guidelines and ConsiderationsNext: Command failed for target `Makefile' © 2010, Oracle Corporation and/or its affiliates Skip Navigation Links Exit Print View Solaris 10 Release Notes Search Scope: This Document Loading patches installed on the system... [...] Loading patches requested to install. [...] Checking patches that you specified for installation. [...] Approved patches will be installed in this order: [...] Checking Consequently, the utility cannot run in a zone.

The usr file system is mounted on c2t0d0s0. Type the following command: # /etc/init.d/init.sma restart x86: Pressing the F4 Key During BIOS Bootup Fails to Boot the Service Partition (4782757, 5051157) You are booting a Sun LX50 which has In addition, all mount options that are not specified in the additional-mount-options portion of the previous command inherit the default values that are specified by the system. their explanation Cannot Delete Existing Diskless Clients From the System (6205746) If you use the smdiskless command to delete a diskless client, the command fails.

Solution These errors occur when the pkgadd utility cannot access the checkinstall script due to insufficient permissions. Error: pkgadd failed for SUNWsrspx Install complete. A message that is similar to the following output is displayed.patchadd ~tsk/patches/111111-01 Validating patches... The Solaris OS is now owned by Oracle.

lucreate Command Does Not Create RAID-1 Volumes (5106987) If you use the lucreate command to create RAID-1 volumes (mirrors) that do not have device entries in the /dev/md directory, the command https://docs.oracle.com/cd/E19957-01/819-6531/gcxmq/index.html Diagnosing the problem If none of the resolutions below resolve the problem run the following command and capture the console output from stdout/stderr. The install script uses the Solaris pkgadd utility to install this package. Executing prepatch script...

Have safe and flawless patching! see here Checking installed patches... Create the new boot environment.# lucreate -n newbe -m /:c0t0d0s0:ufs -m /var:c1t0d0s0:ufs -m /usr:c2t0d0s0:ufs In the previous example, the lucreate command creates the newbe boot environment. This example defines the following file systems and mount points.

Pressing the F4 function key to boot the Service partition, when given the option, causes the screen to go blank. Toolbox.com is not affiliated with or endorsed by any company listed at this site. No changes were made to the system. this page Done!

Change to the directory of the Net Connect product. Mount the root file system of the new boot environment.# mount /dev/dsk/c0t0d0s0 /mnt For each mount point that is defined for the boot environment, change the permissions to 755.# chmod 755 The following table lists examples of invocations that execute successfully under RMI but fail under XML/HTTP: Method Invocation Error Message CIMClient.close() NullPointerException CIMClient.execQuery() CIM_ERR_QUERY_LANGUAGE_NOT_SUPPORTED CIMClient.getInstance() CIM_ERR_FAILED CIMClient.invokeMethod() XMLERROR: ClassCastException Cannot Modify

The following example shows a patchadd operation that failed and the error message that is displayed:Validating patches...

Initializing zone product registry. for eCommerce RSA Adaptive Directory RSA Archer GRC RSA BSAFE RSA Data Loss Prevention (DLP) RSA Data Protection Manager (DPM) RSA Digital Certificate Solutions   RSA enVision RSA Federated Identity Manager However, it ismandated that the user should be 'root' to install the package. The checkinstall script is executed with its ownership set to user install, if there is no user install then pkgadd executes the checkinstall script as noaccess.

Solaris Product Registry Administration Utility Fails to Launch in a Zone (6220284) If you attempt to launch the Solaris Product Registry administration utility in a zone, the attempt fails. It could even be the case that Userid noaccess had no access to the license information. This problem can be caused if your binaries were unpacked to the same location MQ binaries would unpack.. http://back2cloud.com/pkgadd-error/pkgadd-error-checkinstall-script-did-not-complete-successfully-solaris-8.php For SPARC based systems, apply patch ID 119015-01, or a later version.

The other day I was patching a Solaris box and was greeted with the following error: This appears to be an attempt to install the same architecture and version of a Consequently, some user processes fail. I had the same error and a simple move solved everything. pkgadd -d Top Best Answer 0 Mark this reply as the best answer?(Choose carefully, this can't be changed) Yes | No Saving...

Package: SUNWsrspx Workaround: After the OS installation is completed, follow these steps: Insert the Solaris 10 Operating System DVD or the Solaris 10 Software - CD 4. The diskless client is not removed from the system databases. The su command does not provide the full system root account environment, path, and privileges. See the man page mount_ufs(1M) for more information.

Workaround: Follow these steps. Remove advertisements Sponsored Links incredible View Public Profile Find all posts by incredible #5 02-22-2010 flash3 Registered User Join Date: Feb 2010 Last Activity: 22 February 2010, 2:00 The following message is displayed: /tmp/bm122834/installm1a4XN/checkinstallp1a4XN: /tmp/bm122834/installm1a4XN/checkinstallp1a4XN: cannot open pkgadd: ERROR: checkinstall script did not complete successfully Always use the command su - root when instructed to log in as root. The following error message is displayed:state:SIOCSTGET: Bad address Workaround: None.

Some com.sun Application Programming Interface Method Invocations Fail Under XML/HTTP Transport Protocol (4497393, 4497399, 4497406, 4497411) If you choose to use the com.sun application programming interface rather than the javax application From MQ stand point. /tmp directory needs to have permissions set to 777 - read/write/execute for all. Code: # ./installcluster --s10cluster Setup . United States English English IBM® Site map IBM IBM Support Check here to start a new keyword search.

The messages are similar to the following example:Preparing to install zone zone1. Run the Net Connect installer.