Home > Parity Error > Parity Error Detected In Dt Data Out Phase

Parity Error Detected In Dt Data Out Phase

SEQADDR(0x18) SCSIRATE(0x0)Aug 12 08:11:55 office kernel: Unexpected non-DT Data PhaseAug 12 08:11:55 office kernel: scsi0:A:15: parity error detected while idle. Check cable connections between the main unit and device. Check cable connections between the main unit and device. kernel: Vendor: PE/PV Model: 1x2 SCSI BP Rev: 1.0 kernel: Type: Processor ANSI SCSI revision: 02 kernel: blk: queue f7fcf818, I/O limit 4294967295Mb (mask 0xffffffffffffffff) kernel: Attached scsi disk sda at http://back2cloud.com/parity-error/parity-error-detected-in-data-in-phase.php

Tag == 0x5. David. Deffexor Moderator et Subscriptor Registered: Aug 17, 1999Posts: 7576 Posted: Wed Nov 16, 2005 2:08 pm Yup, I just made a bad assumption that the tape drive had an active terminator Some SCSI devices for the PC market do not meet the high I/O speed requirements for the UNIX market.

But that doesn't make sense. Tried connecting each SCSI device (2 tape drives, 1 robot) individually in turn. The drive doesnot show up in "cat /proc/scsi/scsi". David Landgren david at landgren.net Wed Aug 20 05:17:50 PDT 2003 Previous message: "parity error detected in DT Data-out phase" during kernel boot encountered.

Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] More information about the freebsd-scsi mailing list Search:[]List[]Subjects[]Authors[]Bodies (mustpickalistfirst) Set Page Width: [ 80 ] [ P.S. For more information of the RHEL errata support policy, please visit: http://www.redhat.com/security/updates/errata/ If you feel this bug is indeed mission critical, please contact your support representative. Able to successfully backup and install using the tape drives and robot.

REQUEST SENSE ERR Displayed when SCSI interface protocol ended abnormally. SEQADDR(0x1a6) SCSIRATE(0x0) Nov 7 03:30:14 shrek kernel: (scsi0:A:0:0): parity error detected in Message-in phase. Same problem seen as under Redhat. Visit Website Both internal cable ends are instead terminated by plug-in connectors.

Since this bug does not meet that criteria, it is now being closed. I took out the HD and re-installed the OS in a non-raid configuration but now that HD will go offline after just a couple of minutes. kernel: scsi2: scanning scsi channel 3 for logical drives. OS installed on mirrored SCSI drives.

NEGOTIATION ERROR Displayed when SCSI interface protocol ended abnormally. During the maintenance phase, only security errata and select mission critical bug fixes will be released for enterprise products. DISCONNECTED ERR Displayed when SCSI interface protocol ended abnormally. Other possible causes of this problem are improper cabling or termination, and power fluctuations.

Logged ... navigate here SEQADDR(0x18) SCSIRATE(0x0)Aug 12 00:10:55 office kernel: Unexpected non-DT Data PhaseAug 12 00:10:55 office kernel: (scsi0:A:1:0): No or incomplete CDB sent to device.Aug 12 00:10:55 office kernel: scsi0: Issued Channel A Bus In either case, when I run 'camcontrol devlist' it does not show up. DATA OUT ERROR Displayed when SCSI interface protocol ended abnormally.

All rights reserved Use of this Site constitutes acceptance of our User Agreement (effective 3/21/12) and Privacy Policy (effective 3/21/12), and Ars Technica Addendum (effective 5/17/2012) Your California Privacy Rights The Well here's the thing. Usually the SCSI host adaptor does it, but sometimes you might want a device to. Check This Out SEQADDR(0x1a6) SCSIRATE(0x0)Apr 16 20:14:55 server kernel: Unexpected non-DT Data PhaseApr 16 20:14:55 server kernel: (scsi1:A:1:0): parity error detected in Message-in phase.

So I need to get a terminator. SEQADDR(0x18) SCSIRATE(0x0)Aug 12 08:11:56 office kernel: Unexpected non-DT Data PhaseAug 12 08:11:56 office kernel: scsi0:A:15: parity error detected while idle. Yes, the backplane is on channel A and at normal I have the Tape Drive on channel B.

I was trying these ports.

that disk (after you burn it, then boot from it) will tell you much more and precisely than what we can "guess" around here Seriously: Those guys know their stuff - Check cable connections between the main unit and device. Home | New | Search | [?] | Reports | Requests | Help | NewAccount | Log In [x] | Forgot Password Login: [x] | Report Bugzilla Bug Legal CentOS The In my messages log I get the following boot messages:Apr 16 20:14:55 server kernel: scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0Apr 16 20:14:55 server kernel: Apr 16 20:14:55

Attempting to abort.Aug 12 00:10:56 office kernel: (scsi0:A:0:0): Unexpected busfree in Message-in phaseAug 12 00:10:56 office kernel: SEQADDR == 0x16bAug 12 08:11:55 office kernel: Unexpected non-DT Data PhaseAug 12 08:11:55 office One suspicious item is that the unit was not delivered with a terminator. OK.CPU0: Intel(R) Pentium(R) III CPU family 1133MHz stepping 01per-CPU timeslice cutoff: 1462.55 usecs.task migration cache decay timeout: 1 msecs.Booting processor 1/0 eip 3000CPU 1 irqstacks, hard=c03f2000 soft=c03d2000Initializing CPU#1Calibrating delay using timer http://back2cloud.com/parity-error/parity-error-detected-in-data-in-phase-linux.php Maybe I failed to terminate the drive properly.

Device may be physically damaged. Check cable connections between the main unit and device. Sigh.... It then shows a diagram of the drive being the second to last device on the chain with the last device being a terminator.

So does the Error 60000 and sugg bt, driver bt, and host bt.Right now I'm just wondering if I have everything with the tape drive set properly. Top Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost timeSubject AscendingDescending Post Reply Print view 6 posts • Page 1 of 1 Return BIOS == selector * 2). It seems as my HD is going offline after a couple of minutes and does not come back online.