Used diluted napisan (oxygen-based cleaning agent in the ratio of 1:3 with powder:water) and soaked paper towel6. It can get stuck over at the station that cleans the wiper. If youre not technically minded dont bother.Dave http://www.inkjetonline.com.au by unknown on Aug 31, 2006 at 1:50am Add comment Please sign in to comment thanks it worked, something had fallen in and All of your entries were extremely helpful, and I wanted to say thanks to all! http://back2cloud.com/error-code/pixma-mp600-error-6a00.php
i just pushed on it a few times to loosen it up. It has recently developed a problem I cannot figure out. I moved the plastic spring loaded purge a few times and the problem did correct itself. I had tried moving the cartridge cover to the left with no success.
You were exactly right, that little sponge had popped up. Usually because of so much ink , it will be darkuse a pen tip popped both “sponges” out and rinsed them with water and check that they were once again white. I'm about to take it back, any other suggestions?
Ieven looked at printer for sale on the website! Cleaned up some excess ink and reassembled the printer.Thanks inkjetonline! i have a big science proj and when i really needed a printer my canon pixma ip4000 dies on me. Canon 6a00 by unknown on Jan 18, 2009 at 2:37pm Add comment Please sign in to comment 0 My guess is that it's the wiper thing over on the far right of the
This is what happens - (the orange light flashes 11 times). Canon Mp600 Error Code 6a00 Thank you!! - Anonymous That's thrue.I could push the sponge back on his place and after restarting the error 6A00 was disappeared.Thanks - Anonymous It works!!!!!! Would rather break it than pay $80, I'd be better off buying a new one at that point. I see a lot of people bashing Canon, but as long as it's under warranty, they replace it quickly.
After doing that and putting it all back together, problem solved.Thank you guys so much. Canon Mp530 Check Printer 6a00 Gave the white thing a little nudge, it moved, turned it back on and alls ok again! Repeat until the paper towel is relatively clear.5. I used my pen tip and pushed that piece forward and found that the rectangular "sponge" had stuck out of its place.Whichever way it gets stuck, it seems this is an
I tried what you suggested and it worked!Cheers for the info - Anonymous Thanks to you all - I investigated this on my Pixma IP6600D and it turns out there was THe "squeegee" mechanism was not readily noticeable when moving the head to the left on ours, it was to the right behind the front right casing. Canon Printer Error Code 6a00 I put a brand new one and did a printhead cleaning. Canon Printer Error 6a00 Mp610 Pushed carriage to far left (should slide easily)4.
by Anonymous on Aug 21, 2007 at 9:10pm Add comment Please sign in to comment 0 My home recent took a lightning strike and I lost several electronic items but have see here Still the same error. Wearing my blackened fingers as a badge of merit! Doing printhead cleans wastes ink but its an important part.Do a test print of a small amount of text in different colours. Error Code 6a00 Canon Pixma Ip6600d
No change in behavior. Please help me before I lose my senses!Nita by unknown on Sep 22, 2007 at 2:53pm Add comment Please sign in to comment 0 hell my by Anonymous on Sep 23, Error is gone!Thanks again! this page Direct Support 62.459 προβολές 6:39 REFILL KIT FOR CANON PIXMA MG / MX Series That Use CL241 and PG240 Cartridges - Διάρκεια: 19:49.
Be persistent as it took a number of cleanings before getting it too work. Canon Pixma Mx850 Error Code 6a00 With all your helpful hints and instructions, we cleaned under where the ink cartridges rest and came across a penny that had become lodged in the tray, preventing the white L-shaped I prodded, poked, sweated, got covered in ink and nearly set my printer on fire by suicidally lighting matches to see inside the damned thing.
The problematic behavior remains the same. I still can't print from the top feeder, only from the bottom feeder. Oh, well, back to HP. Canon A6000 Now that the power is off, you can move the printhead asm to the far left and this will give you a little more room to access the purge unit.
There is a little white part on the far right. Thank you! Drucker ausschalten2. Get More Info It looks a little like the film on the bottom of the print head.
I have a Canon MP830 and did the same as "briceg", except only onces. Here's what I did:1) Turn off Printer2) Open the printer3) Move the ink to the left4) Look in the space to the right where the cartridges usually stay and there is When I was working in the area of the purge cleaning station, I seem to have dislodged a clear (in color), flexible, rubber (or plastic) part that is approximately an inch Did you ever figure out how to get yours to move to the center?
The sponge then drops back down when finished. Exact same story for me with a new MP970. by unknown on Mar 12, 2007 at 12:29am Add comment Please sign in to comment Your A600 is a paper path error, usually related to the purge unit. A slow computer with inadequate RAM, Windows 95 and 98 (hated them) and finally a really bad printer design that I eventually gave up on and threw out with total contempt.
The other end I just looped onto a tab sticking out of the bottom of the chassis. by unknown on Mar 6, 2008 at 5:55pm Add comment Please sign in to comment 0 Hi I dont know if anyone can help me, But I have a new canon Once you open the cover, the printer should move the carriage to the center to allow you to remove/replace ink carts. I cannot power on, I need to move the carrier manually without power.