Home > Error Code > Payne Furnace Error Code 31

Payne Furnace Error Code 31

Contents

Mi Heating Guy 275 προβολέςΝέο 8:12 Fix for Clogged Drainage ( error code 31 ) on Bryant High Efficiency Gas Furnace - Permanent Repair - Διάρκεια: 13:33. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. It should start the ignition sequence. I can funnel water into the condensate drain and it drains right out the side of the furnace. navigate here

If not you may need a new switch and they do fail. The CORRECT means to diagnose why a pressure switch is opening is to connect a suitable manometer to measure the pressure that the manometer is sampling. Isn't the trap just that -- a trap? Forums | Articles | Home Repair | Home Improvement | Painting | Interior Decorating | Remodeling | Landscaping Blogs Recent Entries Best Entries Best Blogs Blog List Search Blogs DIY

Carrier Furnace Error Code 31

Don't push it or you may strip the gears. CalQwax 765.417 προβολές 9:34 Carrier furnace 59SC5A080 another pressure switch fault code #31 - Διάρκεια: 7:00. Of course it's always possible you have a bad pressure switch. We did not discuss that the pressure switch itself could possibly be bad.

You can take the 2 wires off of it and tape them. I assume that if air can move through it (by blowing) then vacuum pressure can move through it. Hoses are routed correctly as according to the manual and it has been working flawlessly for 8 years. Expert: Tim H. Bryant Furnace Pressure Switch The fact that you hear water gurgling is not a good sign.

It's been one of 'those days'. Bryant Furnace Code 31 Once I removed all of the lines from the trap, water started pouring out. Expert: HVAC Guru replied4 years ago.

themrhelperguy 13.687 προβολές 7:01 Carrier 8000 - Diagnose and Repair Limit Switch - Διάρκεια: 8:29.

It read about .8 ohms...so it was letting the electricity through at room temps. Carrier Weathermaker 9200 Error Codes Carefully remove them and look at them with a magnifying glass to see if any of the pins are pushed back. Expand» Details Details Existing questions More Tell us some more Upload in Progress Upload failed. Remember Me?

Bryant Furnace Code 31

You didn't give me the model number (which would be helpful), but it sounds like this is a 90% furnace. This is the very small thermostat located on the burner housing with two wires going to it. Carrier Furnace Error Code 31 I fell in my pool that had been treated with diatomite, what are the side effects? Bryant Plus 90 Error Code 31 All information is provided "AS IS." Website operating problems contact .

Pressure switch (HK06NB123) failure (or open too long.) Here's what I have done -- removed both lines from the pressure switch and blown air through them. check over here This answer was rated: ★ ★ ★ ★ ★ Payne furnace showing code #31. I believe it is uncommon for the pressure switch itself to go bad after a new install that has been working for many months straight. I maintain that the information that is essential to diagnosing the reason a pressure switch isn't closing is measuring the pressure being applied to the pressure switch. Carrier Furnace Troubleshooting Codes

Reply With Quote « Previous Thread | Next Thread » Thread Information Users Browsing this Thread There are currently 1 users browsing this thread. (0 members and 1 guests) Tags for The question at this point is...why is the water not draining through the condensate trap. Checked tube and nipples at switch and vent wall. his comment is here The igniter still would not glow.

Bryan Sees 37.425 προβολές 3:52 Furnace Troubleshooting: Hot Surface Ignitor - Διάρκεια: 3:59. Bryant Plus 80 Error Code 31 Where should I check next? About the only time a pressure switch should be replaced is when the pressure being measured is normal but the pressure switch doesn't open.

Fan comes on, then inducer motor, but igniter will not ignite.

There's no possible way that fluid has backed up as far as the pressure switch. You can change this preference below. Κλείσιμο Ναι, θέλω να τη κρατήσω Αναίρεση Κλείσιμο Αυτό το βίντεο δεν είναι διαθέσιμο. Ουρά παρακολούθησηςΟυράΟυρά παρακολούθησηςΟυρά Κατάργηση όλωνΑποσύνδεση Φόρτωση... Ουρά παρακολούθησης Ουρά __count__/__total__ Carrier also, should I check fresh air inlet pipe for obstructions too or just exhaust vents Attached Thumbnails Last edited by thealexdexter; 12-06-2008 at 12:09 AM. 12-06-2008, 12:06 AM Hk06nb124 I replaced the the control board and igniter with OEM replacements.

Ask Your Own HVAC Question Customer: replied4 years ago. no moisture in tubing, how would I know/check if there was moisture in the pressure switch. Check the tubing to them, make sure they are not cracked. http://back2cloud.com/error-code/payne-furnace-error-31.php Maybe something is hooked up wrong????

Check the chimney for obstructions. If you check the pressure and it's marginal --- then I'd ignore the pressure switch in favor of checking the furnace system to identify and correct the problem causing the marginal I have gone outside and the supply vent and return vent are both moving quite a bit of air (so the induction motor) is running.