Home > Beep Codes > Phoenix Bios Post Error Beep Codes

Phoenix Bios Post Error Beep Codes

Contents

To find out more information on Phoenix beep codes you can go here. In the event of a fatal system error during initialization, the code representing the portion of the POST causing the failure will be the last value sent to port 80h. Replace the IC if possible 2-1-4 64KB RAM failure Bit 3; This data bit on the first RAM IC has failed. Find us on Google+ System Specific Diagnostic and POST Error Messages: IBM Diagnostic Error Codes Compaq Desktop Systems Diagnostic and POST Errors BIOS Related Pages: BIOS Data Area BiosCentral Forums BIOS news

However, because of the wide variety of models shipping with this BIOS, the beep codes may vary. Replace the IC if possible 1-3-4 First 64KB logic failure The first RAM control logic has failed 1-4-1 Address line failure The address line to the first 64KB RAM has failed Powers on, no tone. Beep Code Descriptions 1 short DRAM refresh failure 2 short Parity circuit failure 3 short Base 64K RAM failure 4 short System timer failure 5 short Process failure 6 short Keyboard

Phoenix Bios Beep Codes

Replace the CPU Low 1-1-2 System board select failure The motherboard is having an undetermined fault. Replace the controller if possible 3-1-2 Master DMA register failure The DMA controller had failed. Failure of the extended area is often due to wrong data setup. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary.

Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed. ALE/IRQ status, Request, LA and memory read/write CMOS RAM Test with walking bit pattern ROM BIOS Perform checksum on ROM BIOS where all bits are added and compared to a factory Replace the video adapter if possible 3-4-1 Video initialization failure There is a problem with the video adapter. Hp Beep Codes Replace the IC if possible 1-3-1 RAM refresh failure The RAM refresh controller has failed 1-3-2 64KB RAM failure The test of the first 64KB RAM has failed to start 1-3-3

Replace the IC if possible 4-2-4 Unexpected interrupt in protected mode This is a CPU problem. Phoenix BIOS beep codes Below are the beep codes for Phoenix BIOS Q3.07 OR 4.X Beep Code Description and what to check 1-1-1-1 Unconfirmed beep code. If possible, replace the MPU Beeps Description 1-1-1-3 Verify real mode 1-1-2-1 Get CPU type 1-1-2-3 Initialize system hardware 1-1-3-1 Initialize chipset registers with initial values 1-1-3-2 Set in POST flag http://www.bioscentral.com/postcodes/phoenixbios.htm If a fatal error occurs, the PhoenixBIOS 4.0 will attempt to issue a beep code representing the error, and it will also attempt to display the error code on a monochrome

These beeps are coded allowing the user to diagnose the troublesome component. Award Bios Beep Codes Bios Central, or any person associated with Bios Central takes no responsibility for any dmage resulting from the use of this information. I verified this with a SIIG (crap -- avoid like the plague) Ultra-66 card, and then confirmed the results with Dell. Replace if possible 1-4-3 EISA fail-safe timer test Replace the motherboard 1-4-4 EISA NMI port 462 test Replace the motherboard 2-1-1 64KB RAM failure Bit 0; This data bit on the

Asus Beep Codes

Press F1 to start the boot process or F2 to enter Setup and change any settings Real-time clock error Real-time clock fails BIOS test. Replace the IC if possible 2-2-3 64KB RAM failure Bit 6; This data bit on the first RAM IC has failed. Phoenix Bios Beep Codes Although Bios Central has used reasonable effort to ensure accuracy we are unable to verify all codes posted. Gigabyte Beep Codes Replace the CPU and retest 4-3-1 RAM test failure System RAM addressing circuitry is faulty.

If your computer has an irregular POST or a beep code not mentioned below, follow the POST troubleshooting steps to determine the failing hardware component. navigate to this website Run Setup and reconfigure the system either by getting the default values or making your own selections System RAM failed at offset: nnnn System RAM failed at offset nnnn of the Replace the IC if possible 2-4-4 64KB RAM failure Bit 15; This data bit on the first RAM IC has failed. Replace the IC if possible 2-2-2 64KB RAM failure Bit 5; This data bit on the first RAM IC has failed. Phoenix Bios Continuous Beep

Startup tone, drive spins, no video Problem with video controller. Replace the CMOS if possible 4-4-1 Serial port failure A error has occurred in the serial port circuitry 4-4-2 Parallel port failure A error has occurred in the parallel port circuitry Replace the IC if possible 4-2-4 Unexpected interrupt in protected mode This is a CPU problem. More about the author Run Setup to be sure the fixed disk type is correctly identified Fixed Disk 1 Failure Fixed disk is not working or not configured properly.

Repeating Short Beep No Power, Loose Card, or Short. 1 Long and 1 Short Beep Motherboard issue. 1 Long and 2 Short Beeps Video (Mono/CGA Display Circuitry) issue. 1 Long and Phoenix Bios Beep Codes 1-3-4-3 Replace the motherboard 4-3-3 Interval timer channel 2 failure The system timer IC has failed. To check all of the components in the PC, the POST program sends out a signal to each device initialising each device's built-in self-test procedure.

All rights reserved.

AMI BIOS beep codes Award BIOS beep codes Dell beep codes IBM BIOS beep codes Macintosh startup tones Phoenix BIOS beep codes Motherboard help AMI BIOS beep codes Below are the Beep Code Description No Beeps No Power, Loose Card, or Short. 1 Short Beep Normal POST, computer is ok. 2 Short Beep POST error, review screen for error code. Perhaps by an application program that changes data stored in CMOS. Intel Beep Codes Replace the IC if possible 2-3-2 64KB RAM failure Bit 9; This data bit on the first RAM IC has failed.

Replace the CMOS if possible 1-1-4 BIOS ROM checksum error The BIOS ROM has failed. If the computer passes the POST, the computer may give a single beep (some computers may beep twice) as it starts and continue to boot. As any experienced technician knows, a failure at any given location does not necessarily mean that the particular part or section under test has actually failed. click site Run Setup to be sure the fixed disk type is correctly identified Fixed Disk Controller Failure Fixed disk is not working or not configured properly.

Failure here is normally due to the CPU, keyboard controller, CMOS chip or an address line PIC Test counter 2 NMI Check for non maskable interrupt request vector for active status. Replace the IC if possible 2-4-1 64KB RAM failure Bit 12; This data bit on the first RAM IC has failed. Might require motherboard repair Shadow RAM failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64KB block at which the error was detected System battery is dead - Failure is normally due to the CMOS but could also be the BIOS IRQ or CPU chips Keyboard Check for NumLock and/or Caps and Shift keys Mouse Initialize through the keyboard

Below are some common beep codes for AMI and Phoenix BIOS. Replace the IC if possible 2-1-3 64KB RAM failure Bit 2; This data bit on the first RAM IC has failed. With a Dell computer, a 1-2 beep code can also indicate that a bootable add-in card is installed but no boot device is attached. Video (EGA) Display Circuitry. 3 Long Beeps Keyboard or Keyboard card error. 1 Beep, Blank or Incorrect Display Video Display Circuitry.

If it cannot locate the address, it displays ??? two-tone siren Low CPU Fan speed, Voltage Level issue Additional information Additional information on the POST and how a computer works? Beep Code Description / What to Check 1-1-1-3 Verify Real Mode. 1-1-2-1 Get CPU type. 1-1-2-3 Initialize system hardware. 1-1-3-1 Initialize chipset registers with initial POST values. 1-1-3-2 Set in POST When a device fails the first part of the POST the BIOS will send a series of beeps from the PC's speaker (internal) to inform the PC user that there is

YesNo Feedback E-mail Share Print Search Recently added pages View all recent updates Useful links About Computer Hope Site Map Forum Contact Us How to Help Top 10 pages Follow us However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary. Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed. Replace the IC if possible 2-3-3 64KB RAM failure Bit 10; This data bit on the first RAM IC has failed.

Bios Central is a trademark of Bob Hurt. Was this page useful? Requires repair of system motherboard Return to Top Phoenix BIOS Post Procedures: CPU Check internal operations i.e. Use at your own risk.

Replace the IC if possible 3-1-1 Slave DMA register failure The DMA controller has failed. Replace the CMOS if possible Low 1-1-3 Extended CMOS RAM failure The extended portion of the CMOS RAM has failed. Home· Forums· About Us· Awards· Contact Us· Upgrade your BIOS BIOS UPDATES Click to scan for Bios Updates BIOS PostCodes Acer ALR AMIT/AMI Arche Legacy AST AT&T Award Chips & Technologies I verified this with a SIIG (crap -- avoid like the plague) Ultra-66 card, and then confirmed the results with Dell.